1/2-inch drywall is the most versatile board and the most common thickness for the 16-inch on-center interior walls in most homes. It offers a good balance between strength and weight. 5/8-inch drywall is a heavier product that resists sagging in ceilings and in 24-inch on-center interior walls.
Can you use 3/8 drywall wall?
You can probably get by with 3/8″ on the walls but unless the ceiling is 16″ on centers I wouldn’t use it myself. Besides sags as said by others, you will likely find it will be rather EZ to damage. use 1/2″ or better yet 5/8″ drywall, OSB is ugly & it stinks (as in malodorous).
Where can I use 1/4 inch drywall?
Quarter-inch drywall is often used to cover damaged plaster walls and also for curved areas because it bends easier than thicker drywall. Then the 1/4-inch-thick drywall can be double layered to get to the conventional 1/2 inch thickness to match the rest of the wall.
When should you use 5/8 drywall?
5/8-Inch-Thick Drywall
These panels are commonly used for ceilings or for walls that require a prescribed fire-resistant rating.
How long should drywall screws be for 1/2 inch drywall?
Choosing the right drywall screw
Most common — 1-1/4”: Use 1-1/4” drywall screws to secure 1/2″ drywall installed on wood-stud walls. These coarse-thread screws typically feature phosphate coatings, which better protect against rust compared to zinc coatings.
Which is better drywall or sheetrock?
No, there is no difference between Sheetrock and drywall. Sheetrock would likely be the standard for what drywall should be. If you see in a tutorial that you should use Sheetrock, you can use any type of drywall available to you. Whether the drywall will be as high quality as Sheetrock is a different question.
Is it OK to hang drywall vertically?
How to Hang Drywall on Walls: Vertical or Horizontal? On commercial jobs, fire codes often require seams to fall on the entire length of the framing, so the drywall must be hung vertically. However, on residential jobs, the drywall on the walls is typically hung horizontally.
What is thinnest drywall thickness?
¼” Drywall: This is the thinnest sheet of drywall available. It is the ideal choice for remodeling your basement, or for any residential interior walls and ceilings that do not require thick reinforcement.
What size drywall should I use in garage?
For the majority of your garage, you can use standard 1/2 inch drywall. For the ceiling and wall abutting the house (if this is an attached garage), you should use 5/8-inch sheetrock or type X fire-rated drywall. Always check your local building codes. There is a code for everything, and your drywall is no exception.
Is it OK to drywall over plaster?
If your walls in your house are ugly or dull because of plaster that is past its prime or not to your taste, you can cover the plaster with drywall. It’s as simple as just putting the drywall sheets right over old plaster. By using some sheets you can cover up old imperfections without a lot of complications.
How much does a 4×8 sheet of drywall cost?
Drywall Prices
The average price for drywall and sheetrock is $15 per 4′ x 8′ panel, with a typical range of $12 to $20 per panel. This translates into a cost of $0.40 to $0.65 per square foot. For walls and ceiling for a 200 square-foot room, you can expect to pay $300 to $500.
Is it OK to drywall over popcorn ceiling?
Scraping the old popcorn texture off may not be an option, but installing new drywall right over the old popcorn ceilings is possible with the right tools and a bit of hard work. Old popcorn textured ceilings (also called acoustic ceilings) make a room look dated.
Does double drywall reduce sound?
Double Drywall benefits
The benefit of a double thickness of drywall with Green Glue sandwiched between is less noise penetration. The drywall adds mass, which prevents sound wave penetration, especially lower frequency, and the Glue absorbs sound vibration-damping sound vibration movement.
What is the difference between 1 2 and 5/8 drywall?
All the inconsistencies between the studs are gone giving the walls a much better finish overall. Another reason the 5/8″ is better for soundproofing is the obvious, the thickness. More thickness means more mass and more mass means better soundproofing. The 5/8″ is also more durable sheetrock versus the 1/2″ option.
What is ultralight drywall?
Ultralight drywall is a generic term for a building material that is about 25 percent lighter than standard drywall. A panel of 1/2-inch thick ultralight drywall weighs 13 pounds less than standard 1/2-inch thick drywall sheets.
What are the two types of seams between drywall sheets?
When installing drywall flat against a stud, there are two types of drywall joints, or seams, you can make: the butt joint or the tapered joint. In many cases, the type of joint you use is dictated by the application. But in a few instances, you may have a choice between butt and tapered joints.
Should drywall joints be tight?
Hanging Drywall Vertically: Leave a 1/8-in.
It’ll usually just cause trouble. Jamming in a piece that’s too tight will crumble the edge or break out a corner (left). And removing a piece to shave a too-tight edge is messy and time consuming. A loose fit avoids this problem.
Should I use coarse or fine drywall screws?
Fine-thread drywall screws are best for installing drywall to metal studs. Coarse threads have a tendency to chew through the metal, never gaining proper traction. Fine threads work well with metal because they are self-threading. Fine-thread drywall screws do not hold as well in wood as do coarse-thread screws.
