Zinsser Bulls Eye 123 Primer is a fast-drying white-pigmented acrylic latex (water-thinnable) undercoat. It is formulated for use on most types of exterior and interior surfaces – previously painted or new work. Any oil or latex finish paint can be applied over Zinsser Bulls Eye 1-2-3.
What is the difference between Zinsser BIN and Bullseye 123?
The quick dry formulation gives Bulls Eye 1-2-3 a 30 minute drying time with a 1 hour recoat time. Zinsser B-I-N is a shellac-based alternative to Bulls Eye 1-2-3 and is perfect for interior priming or for exterior spot priming.
Can I paint over bullseye 123 primer?
Yes you can paint over that – just make sure it is properly dry. Also if you are doing two coats over it make sure you also leave a good amount of drying time between. BE123 seems to slow the drying process a little and you will find the paint dragging if you try and second coat to soon.
When can you paint Zinsser 123?
DRY & RECOAT
Allow more time at cooler temperatures. Dries to touch in 5 minutes and can be topcoated in 30 minutes with latex or oil-based paints. For best results, allow primer to cure overnight before applying strong solvent- based topcoats.
Can I paint over Zinsser 123?
Can You Paint Over Zinsser 123? If it is properly dried, you can paint over it. Make sure you leave enough time between coats if you are doing two coats over it. It seems that BE123 slows the drying process a little, and if you try and apply a second coat soon, you will notice the paint dragging.
Do you need two coats of Zinsser 123?
Application– Ready to use – no dilution necessary. In most cases only one coat is necessary. Porous surfaces may require two coats to properly seal. Prime entire surface for best results.
What is Zinsser used for?
DESCRIPTION AND USES
Zinsser® B-I-N® Shellac-Base Primer is a primer-sealer/stain killer/bond coat recommended for application to interior ceilings, walls, doors, trim, cabinets, furniture and related paintable surfaces. Exterior uses are limited to spot priming only.
Which is the best Zinsser?
Zinsser 123 is great for surfaces that are easier to adhere to and has low odor. Zinsser Cover Stain provides durability and adhesion on glossy glossy surfaces. It’s especially good on raw wood or MDF removing the risk of swelling tat you could get with the water based 123 primer.
Do U sand after priming?
Sand the Primer
Let the primer dry completely, then sand it down before painting. Use very fine 220-grit sandpaper, and apply light pressure to prevent gouging the primer. Remove the primer dust with a quick brush from the shop vacuum, followed by a light swipe of the tack cloth.
Does Zinsser 123 stop damp?
For damp surfaces
Mould can often be a problem in rooms where condensation is common, typically laundry rooms, bathrooms and kitchens. But if you have mould on any walls, inside or out, then sung Zinsser BullsEye 123 Primer will seal in mould staining, stopping it leaching into future layers of paint or wallpaper.
Can I add water to Bullseye 123?
Follow manufacturer’s instructions when using spray equipment. For airless spraying use a 0.017″ tip at 2000 to 2500 psi. Wear NIOSH approved respirator and provide adequate ventilation. If thinning is necessary, add no more than 10 fluid ounces of clean water per gallon and mix thoroughly.
What kind of primer is 123?
About Bulls Eye 1-2-3® Water-Base Primer
Rust-Oleum® Zinsser® Bulls Eye 1-2-3® Water-Base Primer is a wall primer and sealer that provides outstanding performance indoors and out. It features low odor, great flow and leveling, and a flexible, acrylic formula.
Can I use Zinsser primer as a top coat?
Hi Aaron, Primer is not formulated to stand up to the elements and should be topcoated within several weeks to ensure proper bonding. If left uncovered for an extended period of time, primer will tend to deteriorate and chalk, which could prevent future coats of paint from adhering properly.
How soon can I paint after Zinsser primer?
A Zinsser primer can be used over an on. You can paint 30 minutes after drying with latex or oil-based paints, before applying latex paint or applying the oil-based paint for 3 months afterward. A strong solvent-based coating should be applied before primer-freezing.
