Whirlpool Cabrio WTW5700XW has been discontinued. See all Whirlpool Top Loading Washing Machines.
Why is my Cabrio dryer not working?
If your Cabrio dryer won’t run, make sure it is plugged in to a 240-volt power supply and make sure you haven’t pressed the “start/pause” button. When you close the door, make sure it closes completely and is not blocked. If this is not the problem, check the breaker panel or fuse box.
How do I reset my Cabrio dryer?
How to Reset a Whirlpool Cabrio
Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.” Choose a new cycle and press “Start” to begin.Turn off and disconnect the Cabrio if the error or problem persists.Wait several minutes before restoring power.
How do you run a diagnostic on a Cabrio dryer?
Place the dryer is in Standby mode (plugged-in with all indicators off).
Run a Diagnostic Test
Press and Release the first selected button.Press and Release the second selected button.Press and Release the third selected button.Repeat this three-button sequence two more times.
Who makes Cabrio dryers?
Product Description. Whirlpool Cabrio 7.0 Cu. Ft.
Where is Whirlpool Cabrio made?
Today it’s still considered one of the best American made washer dryer options, with their main manufacturing center located in Greenville, Ohio.
When I push the start button on my dryer nothing happens?
If the dryer start switch does not have continuity when it is activated, it will need to be replaced. The door switch is located near the dryer door and is activated when the door is closed. If the door switch fails, the dryer won’t start at all. Most door switches will make an audible click when they are activated.
Does my Whirlpool Cabrio dryer have a reset button?
Doing a factory reset of the Whirlpool Cabrio Dryer is more than simply unplugging the unit and plugging it back in again. You will have to clear the error code, start a new cycle and press the cycle button before you restart the power to the machine. The Whirlpool Cabrio dryer is a popular unit.
Is there a fuse in a Whirlpool Cabrio dryer?
The Whirlpool Cabrio front-loading dryer connects to your home’s fuses through the electrical outlet. Two time-delay fuses are required to provide sufficient power and heat to the appliance without overloading the fuses. If your dryer runs but doesn’t dispense heat, there is a problem with one or more of the fuses.
Where is the dryer reset button?
Generally speaking, you would reset a dryer by pressing the reset button that is located on the control panel. This will help to clear any issues that may be happening with the dryer. It may be necessary to wait until the motor cools down before you push the reset button, but it should fix most problems.
Why is my Whirlpool Cabrio dryer not starting?
Ensure that your household fuses or breakers are active. Whirlpool Cabrio dryers use two time-delay fuses to power up and spin. If one of the fuses has blown, the dryer may come on but not spin or dry. Replace any blown fuses and reset any breakers before trying your dryer again.
Why is my Whirlpool Cabrio dryer not spinning?
If your Whirlpool dryer won’t spin properly, the drum rollers may be worn out. You can check the rollers for wear and tear to see if they turn easily. If any of the drum rollers are damaged or don’t spin easily, we recommend replacing all of them at the same time as a preventative measure.
What does sensing mean on a Whirlpool Cabrio dryer?
All Whirlpool Duet dryers have sensor strips in the drum. As your load of laundry tumbles in the drum, it makes contact with the sensor strips so that the dryer can end the cycle when your laundry is dry. If the dryer is not level, the sensing does not work properly, and your drying cycle will end early.
How do you clean the vent on a Whirlpool Cabrio dryer?
Clean dryer vent and duct
Locate your dryer’s exhaust vent. Unplug your dryer’s power supply cord. Remove any tape or clamps holding the exhaust vent pipe to vent on the back of your dryer.Push the brush from your dryer cleaning kit as gently and as far as possible into either end of your dryer duct.
What does the code PF mean on a Whirlpool Cabrio dryer?
A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.
Can you add an agitator to a Whirlpool Cabrio?
You can easily add the 2 in 1 Removable Agitator to your load or just as quickly remove it and have extra room to wash bulky items.
How much does a Whirlpool Cabrio Platinum dryer cost?
Let’s be clear up front: the is a very expensive dryer. For an MSRP of $1199, this appliance gives you expansive preset cycle options, steam cycles for those with access to a water hose, and capacity that runs on the large end of models available today.
Is Whirlpool Cabrio Platinum dryer gas or electric?
Whirlpool Cabrio; Platinum 7.6-cu ft Reversible Side Swing Door Gas Dryer (White)
