MotionSense™ Touchless Faucets
Touchless Kitchen Faucets with MotionSense feature touchless activation, allowing you to easily turn water on and off with the wave of a hand.
Are touchless faucets worth it?
When you want water on-demand with no mess, touchless faucets are the ideal choice. Some people prefer a touch faucet because it offers more control to the user. It is less likely to accidentally turn the faucet on or off when you have to physically touch as opposed to make a motion in front of it.
How do I change the battery in my Moen touchless faucet?
When the blue LED indicator at the base of the spout flashes, your batteries are low. Open the lid on the battery pack to replace your six (6) AA batteries. [Battery life is approximately one (1) year.]
How do you turn off the bottom sensor on a Moen faucet?
To disable both sensors: Hold your hand directly above the wave sensor for approximately five (5) seconds. Water will begin to run and then turn off, indicating MotionSense Hands-Free has been disabled.
Can a touchless faucet work manually?
NOTE: The sensor cannot be used while the faucet is in manual mode. Find the valve box underneath your sink. Use a coin to turn the bypass counter-clockwise to operate the faucet manually. Turn the bypass clockwise to operate the faucet automatically.
How long do touchless faucets last?
Batteries last from 6 months to 2 years in touchless (as well as touch) faucets.
Do touchless faucets need batteries?
Touchless faucets require a power source to control the sensors and solenoid valves. The power is typically in the form of batteries or AC transformers.
Do all touchless faucets need batteries?
Every touchless or automatic faucet needs a power source in order to work, though the power sources can vary. While some models get their power from dry-cell batteries, other faucets will use a low-voltage current from an AC transformer, Hunker says.
Why is my Moen touchless faucet blinking?
The light will also flash rapidly to indicate battery life is low when using batteries to power the faucet. The blue LED light indicates that you are in electronics mode. It will come on for two seconds whenever electronics mode is activated. The light will also flash slowly indicate battery power is running low.
Why is my touch faucet not working?
When the touch-sensor or motion-activated faucet quits working, the first place to check is the battery compartment. Replace batteries as needed. After replacing the batteries, the faucet make require a reset to work.
How do I turn off my touchless faucet?
Disable:
With the handle in the on position (pulled out away from the faucet), hold your hands over both sensors for five (5) seconds. The front sensor is now deactivated. With the handle in the on position (pulled out away from the faucet), hold your hands over both sensors for five (5) seconds.
How long do batteries last in Moen faucet?
Six AA batteries power the faucet. Under normal operation, they should last approximately one year. To replace them, simply open the battery holder door and remove them – just like replacing batteries in a T.V. remote.
Why is my Moen touchless faucet not working?
Ensure that the data cable and power source cable (battery pack or AC adapter) are plugged in tight and secure. Check Batteries: If using a battery pack, ensure the batteries are installed correctly and are snug in the battery holder. Loose batteries can cause the faucet to operate erratically.
What kind of Moen valve do I have?
Look closely at the handle buttons that were attached to the shower valve. Typically, “Moen” will be written in the middle of the “Hot” and “Cold” buttons. If you do not see this, the handle buttons have been replaced, or the “Hot/Cold” button is a lever (wall escutcheon).
How do you reset the sensor on a Moen faucet?
1. Disconnect the power cable (either battery pack cable or the ac adapter) and the data cable (the flat black cord) from the control box (both the battery pack cable and the ac adapter will be round black cords). Wait sixty seconds with both the power cord and data cord unplugged. 2.
How do you reset a faucet sensor?
To reset a Moen touchless faucet, first, disconnect the power cable. This will either be a battery pack cable or an AC adapter. Next, disconnect the data cable from the control box. Wait 60 seconds with both cords unplugged.
