Hold the WAVE button down for 3+ seconds. The hands will automatically reset to the 12:00 position, and the clock will search for the WWVB time signal. If the clock receives the signal, the clock will set automatically to the correct time.
How do I contact La Crosse Technology?
If you have product questions please contact us via e-mail at or by calling 608-785-7939 M – F 8:30 AM to 5 PM CST.
How do you reset a LaCrosse indoor outdoor thermometer?
Remove all power from both units. Press one of the buttons on the display at least 20 times to clear all memory. Verify that the display is blank before proceeding. Let all the units sit with batteries out for 10 minutes.
How do I reset my weather station?
After removing the batteries, don’t forget to unplug the power cord of the weather station. What you need to do now is press any of the buttons on your weather station a minimum of 20 times. Then you’ll have to wait for at least 15 minutes.
How long does it take for an atomic clock to reset?
Press and hold the “REC” button (D) for 3 seconds. The clock will search for the atomic signal. The clockʼs hands will move to the 12:00 position and the atomic signal will be received within 3-12 minutes. Once the atomic signal has been received, the clock will set itself to the correct time.
Why does my atomic clock not work?
Try powering down the clock (unplug it or remove the batteries), then turn it on again to see if it synchronizes. If the clock uses batteries, check them and replace if necessary. If the radio controlled clock is a desk top unit, try rotating it 90 degrees.
Where is La Crosse Technology located?
Our Location
Nestled in the bluffs of the beautiful Mississippi River Valley in Western Wisconsin, our sales, distribution and customer service staff are all located in La Crosse, Wisconsin.
How do I reset the wifi on my LaCrosse weather station?
If you are using your station connected to the internet, try power-cycling the device to reset the time:
Remove the batteries (if installed)Unplug the unit.Press the LIGHT button 5 times to discharge any stray current.Wait 30 seconds.Plug the unit back in.Re-install the batteries once the correct time is displayed.
How do I manually set my LaCrosse atomic clock?
Set the clock manually:
Press and hold the SET button for 3+ seconds to activate the manual mode. Once the clock is in manual mode, there are two ways to move the minute hand forward. 2. Hold the SET button down to move the minute hand forward consistently.
How do you reset an indoor outdoor thermometer?
Hard Reset
Press and hold the reset button for about 20 seconds. Add batteries to the outdoor sensor. Re-connect the power cord or replace the batteries in the display unit. The reset button must be immediately held for 20 seconds if there is one.
How do I sync my La Crosse remote sensor?
Quick Connect
Bring the outdoor sensor and weather station together inside, and place the units 5- 10 feet apart with nothing between them.Hold the TEMP button for 5 seconds. Remove battery cover from the outdoor sensor and press and release the TX button to send the signal.
Where is the reset button on my Acurite weather station?
First, locate the reset button inside the battery compartment of the display unit. Press and release this button to factory reset the weather station. Once it is reset, press the GEO button to select the correct region that you’re in.
How do you reset a lacrosse wind sensor?
Sensor Connection
If a sensor is not showing data on your display (dashes), or if the data has not moved up from zero, bring the sensor(s) inside next to the display and remove their batteries. Factory restart the display by pressing and holding the two outermost buttons until everything resets.
Why is my Acurite outdoor temperature not working?
If the outdoor temperature is showing dashes or not changing the units may have lost connection or are experiencing interference. Verify that the A-B-C switch in the battery compartments of both the display and sensor are set to the same letter. You may choose A, B, or C; but both units must match to sync up.
Why is my atomic clock not resetting?
If your clock did not change with Daylight Savings Time (DST), make sure the DST switch on the back of the clock is set to ON. If your clock is off by increments of an hour, the Time Zone (TZ) is set incorrectly. Check the Time Zone switch on the back of the clock. If the problem persists, we have a one year warranty.
How do I sync my atomic clock?
How to Sync Your System Clock to Atomic. Right click the time in the tray of your Taskbar and click Adjust date/time. This will open a Settings window with a number of available options. First, ensure that both Set time automatically and Set time zone automatically are slid to On.
How do you reset an atomic wall clock?
Atomic Clocks may also be set manually and be very accurate. Simply insert the battery, press your time zone and then press the flap just above the left side of the battery. Hold until you reach the correct time and then release.
