Whirlpool Cabrio WTW5700XW has been discontinued. See all Whirlpool Top Loading Washing Machines.
How long do Whirlpool Cabrio washers last?
How long will it last? Top loaders typically have a longer life than front load washing machines. This model should last about 14 years.
How do you troubleshoot a Cabrio washing machine?
Clean all contact areas on the lid and the washer. Try unplugging the washer to allow the control panel to reset. Plug the washer back in and see if the problem resolves. If the door sounds like it is engaging, but doesn’t, it is time to run a diagnostic test.
How do I reset my Cabrio washing machine?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How much does the Whirlpool Cabrio cost?
Uneven wash performance plagued the Whirlpool Cabrio Platinum WTW8800YW. To paraphrase that song from Gypsy, upscale appliances gotta have a gimmick to justify their prices. With its $1199 MSRP, the is certainly high end — it even has the name of a precious metal in its title!
Does Whirlpool Cabrio have agitator?
The Whirlpool Cabrio come in two basic flavors, one with an agitator and the other with an impeller. The impeller or agitator is directly attached to the motor rotor by a short drive shaft that is embedded with a bearing through the bottom of the outer tub.
Who made the Cabrio washer?
Whirlpool – Cabrio 4.8 Cu.
Is the Whirlpool Cabrio Platinum Electric?
Whirlpool Cabrio Platinum 7.6-cu ft Electric Dryer (White)
Are Whirlpool washers reliable?
Yes, Consumer Reports and other similar consumer groups routinely rank Whirlpool among the most reliable brands for washing machines. The company has learned a lot about the appliances in more than 100 years of operation.
What causes a Whirlpool washer not to drain or spin?
If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
What causes a Whirlpool washer not to wash?
If your Whirlpool washer Not Spinning well, you need to check the pump. It could be clogged with debris or defective and needs to be replaced. To check the pump, disconnect the drain line and remove the back panel of your machine. Check for debris with a flashlight, or check with a special tool.
Does the Whirlpool Cabrio have a reset button?
Try the Cabrio Reset Procedure
Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL. Choose a cycle and press START.
How do you reset the code on a Whirlpool Cabrio?
First press PAUSE/CANCEL once to clear the Fault code from the Cabrio display. If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea. (Watch The Cabrio Diagnostics Video); This will reveal any stored Fault codes.
How do I reset the control panel on my Whirlpool washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Why is my Cabrio washer so loud?
The most common noise during spin comes from a worn-out and leaking tub bearing. That’s true for all Cabrios, even though the design is slightly different. You can’t help but hear what sounds like a jet flying over your house as your washer spins faster and faster. It’s not a jet; it’s your washer’s tub bearing!
What size is the Whirlpool Cabrio?
ft. Capacity, 14 Cycles, 5 Temperature Options, Cabrio Wash Plate, 1,000 RPM Spin Speed and CEE Tier I Energy Star Rating: White.
