Step-By-Step Instructions:
Dig the post hole, making it three times the width of the post and at a depth equal to 1/3 to 1⁄2 of the above-ground length of the post, plus 6″ (right). Pour 6″ of gravel or crushed stone into the bottom of the hole. Set the post in the hole.

Can you put pressure treated wood directly on concrete?

Wood in direct contact with concrete, and the dampness often found there, will rapidly decay. To avoid this, use pressure-treated lumber. This is wood impregnated with decay-resisting chemicals, usually chromated copper arsenates.

How do you attach wood to concrete without drilling?

A common way to secure wooden items to concrete without drill is by using epoxy glue systems. This glue is specifically manufactured for these problems. Before opting for this method, you need to thoroughly clean off and dry the wood for them to bond correctly.

Why deck posts should not be set in concrete?

A deck post should always be placed on top of footing, not inside concrete because it can break. The photo on the left shows a post set in a bracket that has been mounted to the top of a footer. The photo on the right shows a post that has concrete poured around it, which can lead to a crack like you see here.

What size footings do I need for a 6×6 post?

FOOTINGS: – Poured concrete footings should be a minimum of 8” wider than the posts (4×4 post – 12” min. width, 6×6 post – 14” min. width), a two level deck or deck with roof – 24”x24”. – The bottom of the footings must be a minimum of 36” below finish grade level.

How deep should a 6×6 post be in the ground?

The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole.

What do you put between wood and concrete?

Anyplace where wood meets the ground or concrete, the lumber must be pressure treated. For additional moisture protection, a gasket or strip of closed-cell foam can be installed between the concrete foundation and the sill plate.

How much weight can a 6×6 post support vertically?

The load capacity of a 3-foot #2 grade 4×4 is 17,426 pounds, and a similar 6×6 is 20,834 pounds or 16% better. However, an 8-foot 4×4 supports 6468-pounds and 2339-pounds at 14-feet, while a 6×6 is 18032 and 10550-pounds respectively – or 64% and 78% more load capacity.

Are fence post anchors vs concrete?

Fences with posts set in anchor spikes are just as stable as fences with posts set in concrete. However, with concrete, your posts can and will rot over time as water seeps into the tiny gap caused by the wooden post expanding and contracting with the changes in temperature through the year.

How do I connect two 6×6 posts?

In my experience, the most common and aesthetically pleasing way to do this would be a half-lap joint with fasteners connecting them (nails, screws, carriage bolts, pegs, etc). At this point you could also use Simpson tie connectors, or two angle braces.

Can I put deck posts on top of concrete?

There are several ways to set deck posts; we recommend attaching the posts to concrete footers above the ground. This helps to prevent wooden posts from rotting. Set footers a minimum of 6” below the frost line for your area to prevent movement during freezing temperatures.

Can deck posts sit on concrete pad?

In order for posts to properly resist varying degrees of weight, posts must rest on and be anchored to concrete footings. It’s important to note that patios and pre-cast concrete piers do not qualify as proper footings for deck construction. To anchor posts to concrete footings, you need to use a post base connector.

How do you bolt into concrete?

Simply drill a hole into the concrete, hold the fixture you’re fastening over the hole, then use a hammer to tap the anchor into the hole. As you drive in the pin, the sleeve expands outward, trapping the anchor in the hole.