The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
What does E2 and F6 mean on Maytag washer?
The F6 E2 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.
What does e5 mean on my Maytag washer?
This alert indicates the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
Does Maytag washers have a reset button?
The Maytag washer doesn’t have a reset button. If you need the reset button, you have to use the ‘Power/Cancel’ button. Push it to stop the current cycle. Select a new cycle and then press ‘Start/Pause.
How do I reset my Maytag washer control board?
Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.
How do I reset my front load washer?
Reset your washing machine
What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a “reset” of the washer.
What does F5 E3 mean on a Maytag washer?
Possible Solutions
The F5 E3 alert indicates there is issue with the lid lock. Do not force the lid open, as permanent damage could occur. Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid.
What does E1 and F9 mean on a Maytag washer?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation.
How do I fix error code uL?
If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
What does F5 and E2 mean on a washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
What does E01 and F09 mean on a washing machine?
Accepted Answer. Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
What does E3 and F6 mean on Maytag washer?
The F6 E3 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.
What does E2 mean on Maytag washer?
An E2 Error code indicates that the washer is still draining after 8 minutes. Check the following: Check that the drain hose is not more than 391 ⁄3″ (100 cm) from the floor. Remove any clogs from the drain hose.
What does f2 mean on a Maytag washer?
Common solutions for: Maytag F/02 – Drain Cycle Too Long
The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. Press PAUSE/CANCEL twice to clear the display.
