To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
Will dryer start if thermal fuse is blown?
Will the dryer run if the thermal fuse is blown? Unlike a thermostat that can reset itself, once a dryer thermal fuse blows, it will need to be replaced with a new one before the dryer will run.
Where is the thermal fuse located on my Maytag dryer?
Dryer thermal fuse (or thermal limiter). This fuse is located on the exhaust duct. If the dryer overheats, the thermal fuse opens to cut off power to the dryer. The thermal fuse cannot be reset–if the thermal fuse is open, it must be replaced.
How do you tell if a thermal fuse is blown without a multimeter?
Testing By Bypassing The Fuse
If you do not have a multimeter, you can also test whether or not the fuse is working by bypassing the fuse itself. Simply detach the wires from the fuse, wire them together using a jumper wire and attempt to operate the dryer.
Why is my Maytag dryer not heating up?
If your Maytag dryer is not heating, it is possible that it is not being supplied with the proper voltage. Most electric dryers require two legs of 120 volts AC that is equal 240 volts. If one leg of voltage is shut off by a tripped breaker or blown fuse, the dryer may be able to run but it will not heat.
Is there a reset button on a Maytag dryer?
Maytag dryers boast several features, including a high performance motor, reduced vibration, moisture sensors, wrinkle-prevention option, variable dry for different items and fabrics, and different temperature settings. One thing that Maytag dryers do not have, however, is a reset button.
How do you bypass the thermal fuse on a Maytag dryer?
Locate and Bypass the Fuse
The thermal fuse will look like a thin strip of white plastic with a wire coming out of each end. In order to bypass the thermal fuse, use electrical tape to tape the two ends together. The thermal fuse will then be bypassed. Turn the dryer on to a heat cycle for no more than 90 seconds.
How do you change a thermal fuse on a Maytag gas dryer?
Instructions
Shut off the power and gas supply. Unplug the dryer to disconnect electrical power. Remove the back panel. Remove the fuse. Install the new thermal fuse. Reattach the back panel. Restore power and the gas supply. Clean the exhaust vent.
What causes a thermal fuse to fail?
A thermal fuse will blow when the temperature gets too high, not when it’s drawing too much current. When it blows, the dryer stops generating heat. It’s necessary to replace it before the dryer will run again. The thermal fuse is different from the thermal cutoff.
Where is the fuse on a Maytag washer?
Maytag washers have a fuse in the lid-switch assembly. Maytag top-loading washers have a fuse in the lid-switch assembly. When you close the lid after adding the laundry and soap, the lid’s plastic switch contacts with the assembly underneath.
Are thermal fuses universal?
Product Description. Thermal fuse WP3392519 shuts off the burner in a gas dryer or the motor in an electric dryer when the dryer overheats. A universal part, widely used in dryers of various brands: Whirlpool, Maytag, Kenmore, Crosley, Amana, Admiral, Estate, Roper, etc.
Where is the dryer reset button?
Generally speaking, you would reset a dryer by pressing the reset button that is located on the control panel. This will help to clear any issues that may be happening with the dryer. It may be necessary to wait until the motor cools down before you push the reset button, but it should fix most problems.
What does a thermal fuse look like?
Thermal fuse shapes and sizes vary. Some are made from plastic; others are metal. Look for a small device about the size of a quarter to about 2 inches long, mounted directly on top of the exhaust duct. A thermal fuse has two wires connected to it.
Why is my dryer running but not heating?
Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element.
