A HydroWaveTM washing machine is designed to operate quieter than a typical washer. Each time the lid is closed, the HydroWaveTM wash system senses the washer load and engages a new smart drive system that produces less noise, reduces wear on clothing and maintains great cleaning performance.
How do I reset my GE HydroWave washing machine?
Motor Reset Procedure:
Unplug the washer for 1 minute from the electrical outlet.Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.
What size is the GE HydroWave washer?
ft. Top Load Washer with 16 Wash Cycles, 700 RPM, Quick Wash, Auto Load Sensing and HydroWave Quiet Agitator.
How long do GE top load washers last?
Traditional top load washers last between 10-12 years, so the need to update was really only because the ole’ washer finally gave up. And it is this reliability that keeps people loyal to top load washers. Top loaders use an agitator that sticks up through the middle of the wash basket.
What causes a GE washing machine not to spin?
A loss of electrical power to the washer will cause a failure to spin. To check for power at the outlet, carefully plug a small table lamp or hair dryer into the wall outlet and turn it on. If it does not work, you may have blown a fuse, tripped a circuit breaker or have a defective wall outlet.
Why is my GE washer not spinning clothes dry?
If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. Check these areas and remove anything that may be clogging the draining system on your washer.
Does unplugging a washer reset it?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Does a GE washer have a reset button?
There is not an actual reset button on a GE washing machine. However, pushing the ‘Cancel’ button will clear any error message between the control board and the cycle control switch. Pressing the ‘Pause’ or ‘Stop’ button will then reset the cycle function.
How do you remove the agitator from a GE Hydrowave washing machine?
Remove the dispenser cup at the top of the agitator. To remove, lift the lock ring at the bottom of the dispenser cup, then remove. Remove the agitator cap by prying it off using a flat-head screwdriver. Remove the agitator bolt, securing the agitator to the bottom of the washer, from the center of the agitator.
Why does my GE top load washer smell?
Washer odors (like mildew) are usually caused by leaving the washer lid closed when the washer is not in use. This does not allow air to circulate and dry out the moisture remaining in the tub area. The air and moisture mixture becomes stagnant and creates an odor.
Is it worth repairing a washing machine?
Repair: If the repair would cost less than 50% of the price of a new appliance and your machine still has several expected years of life left, a quick fix could be a cost-effective solution over replacing the entire washer. An active warranty can also make any repair worthwhile.
What brand washer lasts the longest?
Appliance repair technicians and our product experts agree: Whirlpool is the most reliable washing machine brand in the U.S. Broadly considered a “great-value” manufacturer, Whirlpool offers a wide range of laundry machines at price points that won’t prompt you to turn out your pockets.
How do you fix a washing machine that will not spin?
Redistribute an off-balanced load of laundry. Level an off-kilter washer. Check the power source. Stop using an extension cord. Inspect the spin switch. Stick to high efficiency detergent with a front-load washer. Undo any kink in the hose. Track down a blockage in the drainage system.
