ALPHA Gen One STERNDRIVE – MerCruiser Classic (NEW) $3,139.00. ALPHA Gen One Sterndrive/Outdrive – MerCruiser Classic (NEW) 2022-PY NEW Alpha Gen One Sterndrive 1-Year Mercury Marine Factory Warranty & […]
How much is an Alpha One outdrive?
New 2022 Mercury Alpha-1 Gen II OutDrive – $2,849.00.
How do Sterndrives work?
A sterndrive is a marine propulsion system that is attached to a sterndrive, also known as an outdrive. The drive unit is both the transmission and propulsion. When the captain turns the steering wheel, the entire drive turns. No rudder is needed.
Are outboards better than Inboards?
Inboard motors generally last longer than their outboard counterparts. You can squeeze roughly 1,500 hours out of an inboard before necessary maintenance. Outboards, on the other hand, last about 750 hours on average. So, the inboard option means less maintenance (nearly half) even though they cost more initially.
How long do stern drives last?
It’s also common to expect between 10-15 years out of a well-used sterndrive and transom assembly, and then it’s a matter of continual repairs or replacing it once and for all.
How much is it to replace bellows on a boat?
You can get a shift cable bellows for under $50. The other two will run around $100. You will need adhesive and lubricants specific to the make and model of your boat. Ironically, the time it takes to replace them is less than 30 minutes—after you’ve spent a few hours on the drive.
How much power can a alpha one handle?
The Alpha drives are rated for up to 300HP. Not really sure of max torque but probably less than 300 ft/lb. Some people have success using the Alpha drives with higher HP & torque by avoiding quick holeshots and taking it easy on the throttle. Our warranty does not cover applications over 300HP.
Is Alpha or Bravo better?
Bravo One drives were built to handle more power than an Alpha One. When used for lower horsepower applications, they are practically bulletproof. Second, the Bravo One shifts better because it uses a cone-style clutch in its upper housing.
Can you replace an alpha drive with a Bravo?
There’s a fix for this, and it’s not as difficult as you might think. The big to-do is pulling the engine out, but the Bravo One drive and transom assembly will fit where the old Alpha drive was. In terms of size, the drives are similar, and the height of the propeller shaft is about the same.
What is the difference between alpha 1 and Gen 2?
The Alpha Gen II upper and lower housings are fastened together with two through bolts on either side of the drive along with the front and rear bolts, while the Gen 1 drives use one stud visible on either side. Alpha Ones have two studs under the ventilation plate just above the prop.
Are all Alpha One Gen 2 lower units the same?
All Alpha I’s Lower Unit (not the Pre Alpha with the lift ring/or the pre-load nipple on top of the shaft) are interchangeable. The difference in the gear ratio will be in the Upper Unit. Alpha I Gen II not interchangeable. Meaning a Alpha I upper unit and a Alpha I Gen II lower unit,put together.
Can you keep a stern drive in the water?
To keep water from entering the exhaust hub when storing your sterndrive, leave it in the “down” position or use a waterproof cover.
Are stern drives good in saltwater?
Not many people talk about that, but it just shows the technology in the sterndrive market.” Technology has also improved corrosion protection – especially in the saltwater environment – for sterndrives. “There’s no doubt earlier closed-cooled sterndrives suffered terribly from corrosion,” admitted Ray.
How do I stop my outdrive from growing?
The product you are looking for is Algex. It is a fouling stripper made especially for aluminum, which is what your outdrive legs are made of. When you haul your boat, scrub or power wash off as much growth as you can. Spray on the Algex and let it stand for a good 20 to 30 minutes.
